PDS/PPI Home Page

QUICK SEARCH

Search By Missions

QUICK LINKS

FAQ
Citation Policy
Errata for all volumes
Help for Data Users
Help for Data Reviewers
Help for Data Providers

PDS NODES

PDS Home
Atmospheres
Geosciences
Cartography and Imaging Sciences
NAIF - SPICE
Ring-Moon Systems
Small Bodies

Galileo >> PWS

Galileo Orbiter Jupiter PWS 10 kHz Wideband Waveform Data
GO-J-PWS-2-EDR-WAVEFORM-10KHZ-V1.0	PDS 3 CERTIFIED

Start Time: 1995-12-07 23:30:21 - Stop Time: 2002-11-05 14:17:09

This data set contains the Galileo Orbiter Jupiter PWS 10 kHz Wideband Waveform Data. It includes 10 kHz wideband waveform measurements from the Galileo plasma wave receiver obtained during Jupiter orbital operations. Data were acquired near perijove, satellite encounters, and other selected intervals.

Citiation Information

Title	Galileo Orbiter Jupiter PWS 10 kHz Wideband Waveform Data
Publisher	NASA Planetary Data System
doi	https://doi.org/10.17189/1519678

Top/ DATA/ C040193 /

10KHZ_0401930183

Start Time:	1997-179T13:57:32.790	Stop Time:	1997-179T13:58:31.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930284

Start Time:	1997-179T13:58:34.124	Stop Time:	1997-179T13:59:32.790
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930385

Start Time:	1997-179T13:59:35.457	Stop Time:	1997-179T14:00:34.124
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930486

Start Time:	1997-179T14:00:36.790	Stop Time:	1997-179T14:01:35.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930587

Start Time:	1997-179T14:01:38.124	Stop Time:	1997-179T14:02:36.790
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930688

Start Time:	1997-179T14:02:39.457	Stop Time:	1997-179T14:03:24.791
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930810

Start Time:	1997-179T14:03:48.790	Stop Time:	1997-179T14:04:47.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401930911

Start Time:	1997-179T14:04:50.124	Stop Time:	1997-179T14:05:48.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931012

Start Time:	1997-179T14:05:51.457	Stop Time:	1997-179T14:06:50.124
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931113

Start Time:	1997-179T14:06:52.789	Stop Time:	1997-179T14:07:51.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931214

Start Time:	1997-179T14:07:54.124	Stop Time:	1997-179T14:08:52.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931315

Start Time:	1997-179T14:08:55.457	Stop Time:	1997-179T14:09:54.124
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931416

Start Time:	1997-179T14:09:56.789	Stop Time:	1997-179T14:10:55.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931517

Start Time:	1997-179T14:10:58.124	Stop Time:	1997-179T14:11:56.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931618

Start Time:	1997-179T14:11:59.457	Stop Time:	1997-179T14:12:58.124
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931719

Start Time:	1997-179T14:13:00.790	Stop Time:	1997-179T14:13:59.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931820

Start Time:	1997-179T14:14:02.124	Stop Time:	1997-179T14:15:00.790
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401931921

Start Time:	1997-179T14:15:03.456	Stop Time:	1997-179T14:15:51.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932115

Start Time:	1997-179T14:17:00.790	Stop Time:	1997-179T14:17:59.457
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932216

Start Time:	1997-179T14:18:02.123	Stop Time:	1997-179T14:19:00.790
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932317

Start Time:	1997-179T14:19:03.456	Stop Time:	1997-179T14:20:02.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932418

Start Time:	1997-179T14:20:04.790	Stop Time:	1997-179T14:21:03.456
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932422

Start Time:	1997-179T14:20:07.456	Stop Time:	1997-179T14:21:06.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932519

Start Time:	1997-179T14:21:06.123	Stop Time:	1997-179T14:22:04.790
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932523

Start Time:	1997-179T14:21:08.789	Stop Time:	1997-179T14:22:07.456
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932620

Start Time:	1997-179T14:22:07.456	Stop Time:	1997-179T14:23:06.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932624

Start Time:	1997-179T14:22:10.122	Stop Time:	1997-179T14:23:08.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932721

Start Time:	1997-179T14:23:08.789	Stop Time:	1997-179T14:24:07.456
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932725

Start Time:	1997-179T14:23:11.457	Stop Time:	1997-179T14:24:10.122
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932822

Start Time:	1997-179T14:24:10.122	Stop Time:	1997-179T14:25:08.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932826

Start Time:	1997-179T14:24:12.789	Stop Time:	1997-179T14:25:11.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932923

Start Time:	1997-179T14:25:11.455	Stop Time:	1997-179T14:26:10.122
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401932927

Start Time:	1997-179T14:25:14.122	Stop Time:	1997-179T14:26:12.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933024

Start Time:	1997-179T14:26:12.789	Stop Time:	1997-179T14:27:11.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933028

Start Time:	1997-179T14:26:15.455	Stop Time:	1997-179T14:27:14.122
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933125

Start Time:	1997-179T14:27:14.122	Stop Time:	1997-179T14:28:12.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933129

Start Time:	1997-179T14:27:16.789	Stop Time:	1997-179T14:28:15.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933226

Start Time:	1997-179T14:28:15.455	Stop Time:	1997-179T14:29:14.122
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933230

Start Time:	1997-179T14:28:18.123	Stop Time:	1997-179T14:29:16.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933327

Start Time:	1997-179T14:29:16.789	Stop Time:	1997-179T14:30:15.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933331

Start Time:	1997-179T14:29:19.455	Stop Time:	1997-179T14:30:18.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933428

Start Time:	1997-179T14:30:18.123	Stop Time:	1997-179T14:31:16.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933432

Start Time:	1997-179T14:30:20.789	Stop Time:	1997-179T14:31:19.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933529

Start Time:	1997-179T14:31:19.455	Stop Time:	1997-179T14:32:18.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933533

Start Time:	1997-179T14:31:22.123	Stop Time:	1997-179T14:32:20.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933630

Start Time:	1997-179T14:32:20.789	Stop Time:	1997-179T14:33:19.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933634

Start Time:	1997-179T14:32:23.455	Stop Time:	1997-179T14:33:22.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933731

Start Time:	1997-179T14:33:22.123	Stop Time:	1997-179T14:34:20.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933735

Start Time:	1997-179T14:33:24.789	Stop Time:	1997-179T14:34:23.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933832

Start Time:	1997-179T14:34:23.455	Stop Time:	1997-179T14:35:22.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933836

Start Time:	1997-179T14:34:26.123	Stop Time:	1997-179T14:35:24.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933933

Start Time:	1997-179T14:35:24.789	Stop Time:	1997-179T14:36:23.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401933937

Start Time:	1997-179T14:35:27.455	Stop Time:	1997-179T14:36:26.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934034

Start Time:	1997-179T14:36:26.123	Stop Time:	1997-179T14:37:24.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934038

Start Time:	1997-179T14:36:28.789	Stop Time:	1997-179T14:37:27.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934135

Start Time:	1997-179T14:37:27.455	Stop Time:	1997-179T14:38:26.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934139

Start Time:	1997-179T14:37:30.123	Stop Time:	1997-179T14:38:28.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934236

Start Time:	1997-179T14:38:28.789	Stop Time:	1997-179T14:39:27.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934240

Start Time:	1997-179T14:38:31.455	Stop Time:	1997-179T14:39:30.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934337

Start Time:	1997-179T14:39:30.123	Stop Time:	1997-179T14:40:28.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934341

Start Time:	1997-179T14:39:32.789	Stop Time:	1997-179T14:40:31.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934438

Start Time:	1997-179T14:40:31.455	Stop Time:	1997-179T14:41:30.123
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934442

Start Time:	1997-179T14:40:34.122	Stop Time:	1997-179T14:41:32.789
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934539

Start Time:	1997-179T14:41:32.789	Stop Time:	1997-179T14:42:31.455
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934543

Start Time:	1997-179T14:41:35.456	Stop Time:	1997-179T14:42:34.122
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934640

Start Time:	1997-179T14:42:34.122	Stop Time:	1997-179T14:43:08.788
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

10KHZ_0401934644

Start Time:	1997-179T14:42:36.789	Stop Time:	1997-179T14:43:08.788
This file contains 10KHZ PWS waveform data from the waveform analyzer. The binary file structure is somewhat complex. Users should refer to the pictures in the WAVEFORM.TXT files for additional information. All waveform data files are binary and have a fixed record length structure. The first record is an ASCII header (padded to record length) that contains many of the same parameters contained in this label file. The next record is a binary header that also contains much of the same information as this label. This label is derived from the data file by reading these headers. The binary header record is described in machine readable form by the PDS label file EDRHDR.FMT and in a more human readable for in EDRHDR.TXT. The remaining records contain data. Each data record has a 30 byte header (prefix) followed by n (n=1 or 10) blocks of waveform samples. In most cases, only a few of these data blocks contain data (the rest may be zero filled). The file record length, the number of waveform samples per data block, and the sampling frequency are dependent on the spacecraft telemetry mode and the instrument mode. The following table describes the variations in waveform data files: APID Inst Mode* Tel-fmt Rec-Length Blocks/Rec Samples/Block ID (bytes) --------------------------------------------------------------------- PWH1 1,2,3 LPW 465 1 870 PWH2 1,2,3 MPW 670 10 128 PWH3 1,2 MPP 1630 10 320 PWH3 3 MPP 1080 10 210 PWH4 1,2 HPW 7910 10 1576 PWH4 3 HPW 1080 10 210 PWH5 1,2,3 LPW 4350 10 864 * 1=10 kHz, 2=80 kHz, 3=1kHz Each data record contains data acquired in a single minor frame (mod91=0.667 seconds). The time tag for the data record is located in the row prefix header (ROWPRFX.FMT). The start time of a block of waveform samples is the RTI in which the data block occurs (10 RTI per minor frame, 0-9). Therefore if the waveform samples are located in data block 3 and the row prefix header gives the time tag 03209117:27:0:0, then the samples begin at 03209117:27:2:0. The time between samples is determined by the sampling frequency. There are 3150, 25200, 201600 samples per second in the 1 kHz, 10, kHz, and 80 kHz modes respectively. Please note that in the PWH5 mode, there are more samples than can be taken in a single RTI at the 1 kHz sample rate. The waveform data are sampled uniformly and continuously in a single data block, across the RTI boundaries. These data are non-overlapping so that data cannot occur in all of the data blocks for this mode/format combination.

ICON LEGEND
For links to data holdings various icons are used to represent services or actions you can take. Those icons are:
	Order the volume (CD-ROM/DVD) containing the listed data. The volume will be mailed to you.	The volume (CD-ROM/DVD) contains some errors which are documented in an errata log.
	Launch a custom web browser for the resource.	Launch a map based browser for the resource.
	Toggle viewing into brief mode (shorter descriptions are displayed).	Toggle viewing into expanded mode (longer descriptions are displayed).
	Download the volume containing the listed data.

NEW RELEASES

More.....

PDS RESOURCES

Archive Planning Guide
      Individuals
      Missions
Data Dictionary Search
      Lookup Tool
      Document
PDS4 Standards Documents
PDS Subscription Service

PDS3 Standards

OTHER RESOURCES

ADS Search
Science Data Licenses

	Search For:

	in